|
| |
|
|
|
|
| Sour Oil & Gas Valves |
|
 |
|
|
 |
1/4, 3/8 & 9/16" O.D. tube connections |
|
10,000, 20,000 & 30,000 psi series |
|
Vee and regulating stem types |
|
Annealed 316 stainless steel construction |
|
Meet or exceed requirements of NACE MR0175 |
|
 |
|
|
|
|
|
|
|
|
| Sour Oil & Gas Fittings |
|
|
|
|
A complete range of elbows, tees, and crosses is available for use with sour oil and gas. Material is annealed 316 stainless steel. All connection components and fittings are rated for 30,000 psi service. Standard tubing glands and collars are provided unless otherwise specified. |
|
Connection Components |
|
High Pressure Elbows |
|
High Pressure Tees |
|
High Pressure Crosses |
|
|
|
|
|
|
| Accessories |
|
|
|
|
Union Couplings (Slip Type) |
| Union (Slip Type) couplings are ideal for use in confined space installations. This design allowsthe entire coupling to be disconnected and slipped back over the tubing to facilitate assembly and disassembly. In installations where tubing is easily assembled, it is preferable (and less expensive) to use standard straight couplings (see accessories section). Sour oil and gas material is annealed 316 stainless steel. Standard tubing collars and glands are provided unless otherwise specified. |
Bulkhead Couplings |
| Bulkhead couplings are designed specifically for passing a tubing connection through a panel or steel barricade. These couplings include a locknut as shown. Material is annealed 316 stainless steel. Standard tubing collars and glands are included unless otherwise specified. |
Caps |
| Tubing end caps are offered for use in sealing off tubing ends either for temporary use or permanent use such as on small volume reservoirs. Standard material is annealed 316 stainless steel. Standard tubing collars and glands are provided unless otherwise specified. |
| Line Filters |
| The line filters as shown utilize sintered stainless steel filter discs 3 pc./set. Porosities are available as per the chart to the right. If not otherwise specified, 100 micron filter discs are supplied. (One micron = 0.001 millimeters). Material of bodies and end covers is annealed 316 stainless steel. Standard tubing glands and collars are provided unless otherwise specified. |
Ball Check Valves |
| Ball type check valves insure flow in one direction only. Material for bodies and covers is annealed 316 stainless steel, the ball is 17-4PH. Standard tubing glands and collars are provided unless otherwise specified. |
| Soft Seat Check Valves |
| Soft seat check valves insure flow in one direction only and can be mounted in any position. These are highly reliable for both gas and liquid service. Standard O-ring (soft seat) material for the sealing surface is Buna-N (nitrile) with other materials including Teflon and Viton available on request. Temperature is limited by the choice of O-ring material. Material of all other parts is annealed 316 stainless steel. Standard glands and collars are provided unless otherwise specified. |
| Adapters |
| Connect different sizes of tubing or tubing and pipe with our female-to-female couplings, female-to-male adapters, male-to-male adapters, reducer couplings and thermocouple adapters. For complete adapter information, see accessories section of full line catalog. |
| |
|
|
|
|
|
|
|
|
| Bleed Valves |
|
|
|
|
Tee handle for easy operation |
|
Vent port tapped for safe plumbing |
|
Positive blow-out prevention on stem |
|
Metal-to-metal seat for bubble tight shut-off |
|
One piece hex construction for easy installation |
|
Compatible with standard API test and gauge connections for 20,000 psi |
|
Designed for pressure bleeding |
|
 |
|
|
| Back to Top |
|
|
|
|
| |
|
|
|
